Painless Trail Rocker Accessory Control System for Jeep Wrangler JK 2011-2018
Trail Rocker is the most robust and ruggedized control system for your electrical accessories on your Jeep. Trail Rocker kits allow you to control up to eight electrical accessories on your Jeep Wrangler JK. The heart of this kit is enclosed in the weatherproof housing that surrounds the relay center which houses eight fuses and eight relays. Controlling it at your fingertips are five prewired rocker switches mounted in their custom dash panel for a clean factory-installed look inside your Jeep.
The Trail Rocker kits provide all the necessary weatherproof splices and heatshrink to connect directly to your Jeep's accessories, ranging from lights to air lockers. Easily installed with their detailed instructions and plug-n-play design.
Provided are 5 switches prewired to control 6 accessories with ease. Also included are two extra output wires that are easily wired into one of the 5 existing switches giving you control of up to 8 total accessories.
- Control up to 8 accessories (8) 30 amp fuses and (8) 30 amp relays
- Weatherproof housing around the power center and connections
- Custom bolt-on powder coated bracket for the power center
- Switch panel mounts 5 LED switches in a factory non-intrusive dash location
Winch ready! The Trail Rocker system includes dedicated wires for controlling a winch. Purchase of the Winch Control add-on kit, part number 57150 is required for operation.
Note: Automatic Transmissions Only
- The moment you know you're in good hands. The Painless Trail Rocker comes shipped and packaged to ensure the product arrives to you undamaged.
- The heard of the Trail Rocker is the fuse & relay center. Here you will find (8) 30 amp fuses and (8) 30 amp relays. While the switch panel only comes with six total switches, they provide you with the two extra circuits for doubling up on dual high amp systems. Say for example, (2) 20 amp lights powered off of two relays but only one switch.
- The top of the weatherproof fuse & relay center features the stylish logo silkscreened onto it. Along with the fused power source mounted next to it.
- The 200 amp MIDI fuse comes pre-installed and prewired. There's no worrying about how to crimp that 6 gauge power cable.
The underside of the fuse & relay cover has a built-in gasket to help keep any moisture out and to act as an extra support for the relays. This extra support on the relays ensures that no matter how good or bad you are on the trails, the relays will not pop out of place.
- Attention to detail shows in the bolt with O-ring combo to hold the top cover on.
- Underneath the fuse & relay center, you will find the powder coated custom mounting bracket with stainless hardware. This bracket is designed to install in existing mounting holes under the hood.
- The switches are vibration, shock, thermoshock, moisture, and salt spray resistant.
- The back side of the switch panel comes pre-terminated and ready to plug into the fuse & relay center. They also pre-route the two extra output wires to the panel. This allows you to either piggy back extra components off of a switch, or to replace the on/off switches with more on/off/on options.
- The harness attaches the fuse & relay center to the switch panel. It's a plug-n-play design that only requires you to route it and plug it in.
- Exiting the fuse & relay center is 21ft. of wire to reach any 12 volt accessory you have.
- Printed every 12" on the wire, you'll find the circuit description, a signature of Painless.
- This parts kit comes with everything you'll need to install the Trail Rocker, except the tools and the Jeep. You'll also find a custom pigtail that allows the Trail Rocker to power up only when the key is turned on. The system is shipped to be powered at all times
- You'll also find a winch pigtail that is prewired into the kit. This pigtail is ready to wire up to your winch (not included). The other end is ran up to the switch panel.
- Nearly 50 pages full color manual is also included. |